I’ve been getting a lot of requests lately to do a custom warden and deep dark and while i’m still working on my deep dark biome i have come up with a warden design that i’d like to share with you and what follows are the step-by-step instructions on how to make one of these Guys for yourself let’s get started so these are all the parts here that you’ll need to complete the warden there’s just a few that i do want to draw some special attention to note that these two pips here have the hole in it for a bar this one does not if you have A third one with a hole that’s fine but have at least two this piece here is in trans-medium blue it’s from alpha team mission deep freeze if you don’t have then to have it in that color substituting a translate blue will do just fine everything here is pretty easy To come by except these two pieces which go for about a dollar a piece on bricklink they are very important and so i think shelling out the two or three dollars that i’ll take to get both of these is well well worth it let’s get building We’ll start with the body which uses the biggest piece a two by four so add a jumper corner plate corner plate two horizontal clips one by one tile in tan one by one black plates black pip up here on the side another 1×1 black plate in there take our first of the 1×1 Translight blue plates put it there 2×2 another corner plate one by two tile on tan we’re slowly creating the spine in the back there two more horizontal clips there and this is where i used that trans-medium blue pip but pretty much any transparent blue color will do just fine there then those last Three spaces receive one by one plates in black the other one by one light trans blue goes there two by two on this side corner on that side tan jumper that’s gonna go there last two horizontal clips the one by one without the bar hole through it we’ll go here And then the remaining three places you guessed it more one by one plates and black we’ll also put a one by one plate and black on top of the jumper followed by one and tan and then this clip will go on top of that take the 1×4 plate put that in the front Then these modified one by ones with the bar are going to go here and they’re going to be angled towards the back so if we turn it around that’s what our spine looks like which is pretty cool next you’ll take the last two quarter plates put them there tile this off With one by twos and then we’re just going to put in our teeth and all those clips And what i’ve done is i angle these top ones down ever so slightly have the middle ones as straight as much as i can and then these bottom two curve them up a little bit so you get a little bit more of an interesting shape With that and that’s all there is to the body so the legs are identical we’ll be making the same thing twice tan clip 1 by 2 dark blue on top of that one of these 1 by 2 clips in black this modified one by one with the bar on the End goes on top and then yet another one of these one by one plates in black and you’ll make one more of those and these i’ve just put in a middle anti-stud and you can kind of angle them how you like i have them angled slightly outward as it Makes them look a little bigger when viewed from the front which i definitely think is a good look so his legs aren’t too skinny the arms are nearly identical they’re just mirrored but we’ll start out with stacking two one by twos in black then on the underside of that one one by One in black and then one one by one in dark blue on the top you’ll do the same thing but opposite placements two 1×2 plates in dark blue one by one in dark blue one by one in dark tan another one by one in dark tan then one in Regular tan and then on top of that we’re actually using this snot brick it’s gonna face like that and then the regular one by one no stud on the side we’ll go there and we’ll just top that off with a 1×2 tile in black so now we’re just going to make this Button mirrored Just like that and these go exactly where you probably expect them to go the snap brick will line up with that modified one by one with the bar on both sides so basically you want those regular one by one bricks towards the front and if we angle these just right You can finagle with them quite quite a bit but we get that look which is definitely the look we want right so he’s almost done we just need to get ahead on this guy start out with the two by three again that modified one by one right there Our last two one by one black plates then we gotta make the face on this guy which has a dark bluish outline so we’re going to use dark blue bricks naturally so two cheese slopes facing away from the middle one by one tile there in the center We’re going to take one by ones with a stud on the side they’re going to go on the outside that’s where we’ll attach the ear sensors of sorts and then just a regular one by one in the middle two by three put a 1 by 3 underneath it and then Another 1 by 3 in dark blue that will just go on top and you can see we got our mouth right there we’ll tile this off with the three remaining dark blue tiles and then all we have to do is add the ears so just to make them a little bit Bigger i’ve gone ahead and put these one by ones with again the hole through the middle on the side that allows these plume pieces to fit in there perfectly and of course we have this clip right there just waiting to attach he can actually stand on his own though i would recommend making A base as he does tend to fall over a little bit that’s all there is to it you’ve made a very angry looking lego order in the future i do really want to make a deep dark biome module for my custom series to for this guy to Inhabit i think they’ll be quite fun there’s a bunch of other cool blocks and stuff to put in that module as well which i’m very much looking forward to coming up with concepts for in the meantime though i hope you enjoy this if you do end up creating a warden and Giving him a home be sure to share the pictures with me on instagram or whatever and pretty much cheesy studios everywhere thank you so much for watching have a great life i’ll see you next time You Video Information
This video, titled ‘LEGO Minecraft: Custom Warden Tutorial!’, was uploaded by Cheesey Studios on 2022-07-09 03:15:02. It has garnered 129479 views and 4872 likes. The duration of the video is 00:09:12 or 552 seconds.
You guys have been asking for me to make the Deep Dark since before the update dropped! I’m happy to announce I’ve got one in the works which will feature this custom Warden design! I figure it would be fun to break this one down brick by brick so that you can build your own. Enjoy!
Parts list: https://drive.google.com/file/d/18J7JWdy-n8oa_Ksg5mppUW_V_zvq9l7W/view?usp=sharing