Hey hello my name is Scotty and welcome back to another Minecraft Bedrock edition tutorial I’m back again don’t worry today we have ourselves a 3X3 spiral piston door it’s been a while since I’ve did one of these in today’s story I’m wearing a shark onesie if you Have an idea of a onesie I could use in my next tutorial leave it down in the comment section just keep in mind all the ones up on screen right now are ones I’ve already used anyways let’s just get straight into the materials you’ll need solid blocks 11 sticky pistons 12 door Block one obsidian four observers around 32 Redstone Dust 14 Redstone repeaters 5 Redstone torches and two levers let’s get straight into this so first get out your door block you’re going to have three blocks in the floor three blocks on the left side and the right side and Then three blocks on top like so make this nice little ring next you got your sticky pistons on both the left and the right side you’re gonna get two sticky pistons facing in like so go to the top go two blocks up break the first one get A sticky piston facing down to left of it get another one facing down and to the right of it get another one facing down like so now let’s go down to the bottom on the left side right under this iron block you’re going to get a sticky Piston facing in like so then under this middle bottom door block you can get two sticky pistons facing upward like so into the block and on the opposite side of this piston you’re going to get a block of obsidian this is so this piston won’t like misfire and push the whole Door this way mess it all up we don’t want that so should be looking something like this make sure it does next get out all your Redstone materials and your observers from the front go down to this bottom piston and we’re gonna get Observer facing into it as you can see This arrow is facing into this piston there also should be the face on this side on top of this Observer facing into this top piston we’re gonna get a repeater on four tick delays crash place a block on the back of it and then right below this block right in front of this Face we’re gonna add a Red Zone dust should trigger off this piston leave this block there that’s fine don’t worry about it not a big deal it should do that going off this Redstone Dust going back bringing another repeater three tick delays right above this repeater we’re going to crouch place an observer Facing up as you see this red dot should be towards the sky on top of the Observer you’re going to place a block should be right next to this piston now come back down to the repeater we’re gonna go out one red some dust then we’re gonna go towards the door in the Center break this block right next to this Red Zone dust have a sticky piston facing up and the Observer facing out so the face should be on this thread some dust and the dot should be facing away we’re gonna have this Observer going into a repeater through tick delays Officer Peter going to this bottom piston we’re gonna have an observer facing into it as you see goes this way the face is on the side with this red Sun repeater and we’re gonna have this repeater going into a block in between this Observer and this block we’re gonna Have a redstone dust block next to the Redstone Dust In This piston and have a torch on the side of it block on Top push on the inside and the outside of it like so off this torch we’re gonna have it block Redstone Dust connected up to It going into repeater no tick delay needed crash place a block on top of this repeater right here then on top of this Observer we’re going to have a repeater four tick delay so that’s should be all the bottom Redstone done so we’re going to go back around to the Front find this redstone dust that we first placed in the beginning we’re gonna go two blocks off of that Peter going into this block resident dust behind that block on top of the red some dust get out your lever and we’re gonna place it on top and see if this thing Works as you see should double extend and should double retract and it double retracts perfect now if your door didn’t double the track you’re probably missing something so start this off this is a Minecraft Bedrock edition tutorial this does not work on Java edition if you’re on Java Edition you’re Gonna have to find a new video I’m sorry but if you’re on Bedrock Edition stay here we’ll go over another couple points see if you’re missing something so first make sure you’re using solid blocks Redstone pulses can only go through saw blocks that means no glass no glowstone No sea lanterns nothing similar to those we need solid blocks like Stone and wood next make sure that your repeaters are all on the correct to delay so we have zero we have four we have three we have three zero and four make sure those are all correct now make sure your observers Are all facing the correct direction so we have this one on the bottom the Red Dot should be on this side face should be on the outside this one face should be on the outside Arrow facing this way dot on the inside this one should be Facing into the Piston face should be on the outside and this one people always get so confused because oh my arrow isn’t on this side or on the same side as yours wrong on this wall is wrong it’s not placing correctly yes it is it’s just whether your door is facing This way like mine or it’s facing this way so as long as there’s an arrow facing up you’re all good a lot of things that people forget when building theirs is the block on top of the subserver so make sure you have a solid block right here so make sure you check All those come back around see if it works it should work if it doesn’t join my Discord server there I’ll be more than happy to help you or someone else will be more than happy to help you find out what is wrong with your door and Help you fix it so just head down the link in the description and join it so now it’s time to move on to the top part of the door and making it all spiral so you’re going to place two blocks off of these two blocks Redstone Dust connected Up another repeater four tick delay go in front of this block repeater for tick delay like so have this repeater going into a block with a red zone torch on the opposite side block on top of it redstone torch block off to the side to then connect this resin torch to this Piston with red some dust block on top block off to the side above the Redstone Dust place redstone dust on top of the block with the Reds on Torch repeater no tick delay needed going into a block right above this piston redstone dust on top block on top of this repeater rest Some dust on top of that go another block up towards these Pistons with redstone dust on top then Place three blocks on the side of these pistons and another three blocks going back on top of every single one of these Pistons we’re gonna have a block going into Every single one of these blocks we’re gonna have a repeater first one don’t click it second one click once third one click twice then just connect these up with redstone dust like so then we’re gonna go down one off to the side red some dust on top of that block we’re Then gonna go down one again like so going back towards the door we’re gonna repeat her coming out of this block right here with the Redstone Dust we’re gonna have it on for tick delay place a block for it to go into atop this piston Place block rest some dust on top of That outside of this piston place a block ride some dust on top of that then go down again rest on Dust on top of this block then you gotta go below this piston place a block block going back so the repeater can be coming out of this Block into this piston like so no type delay needs now if we go back around to the front and we try this out it should spiral like so and it should spiral again pretty wonderful next all you have to do is just cover this up so I Finished covering mine up didn’t do a great job you guys will probably do much better job than I’m doing right now but at this point you’re probably just like I don’t want my lever right here I want it over here I want another lever on the inside or maybe you want to activate Your door with I don’t know maybe a pressure plate or button let me show you guys how to do this so if you want to move your lever it’s as simple as just you know moving your lever let’s say I want mine on a wall right here I’m gonna Flick it down and we’re going to connect it up to our activation Point our activation point is right here these two Redstone Dust into these repeaters this is our Activation so we’re gonna do oh okay it didn’t mean to do that we want Redstone we’re going to connect it up Connect it up to our lever like so so as you see it activates it opens and it closes does all the good stuff because it reaches now let’s say you have a super far lever though like let me let me let me just go super far now I have This super far lever and as you can see it’s not working it doesn’t reach the reason it doesn’t reach is because the pulse dies out if your pulse dies out all you have to do is add a repeater somewhere so then it’ll reach down here you may have to add multiple depending On how far away it is just add another repeater should be all good and now it works so you see you flick this lever it works wonderfully let’s say you want another lever on the inside it works the same thing it is the same exact thing as Just moving your lever so we’re going to do is we’re going to have our lever right there just gonna have it go down we’re just going to connect it up to these activation Point connects up to the activation Point oops and it works perfect so I can open it from this end Go through and close it with this end open it go through close it with this end it’s wonderful so whether you’re moving your lever you’re adding a lever you’re adding a t flip-flop with a button or a pulse Extender with a pressure plate or whatever the situation May be all you have to do is add it and connect it to the activation point right here these two Redstone dots make sure it reaches it and make sure it has enough strength to go through these repeaters that’s all you have to do if you’re having any trouble whatsoever and Would like some help join the Discord server links in the description I or anyone else will be more than happy to help other than that hopefully I helped you today if I did make sure to smash like subscribe new as always post noise and I’ll see you guys next one goodbye Video Information
This video, titled ‘EASY 3X3 SPIRAL PISTON DOOR IN MINECRAFT BEDROCK 1.20!!! (PS4,PS5,Xbox,Windows 10,MCPE,Switch)’, was uploaded by ScottyO on 2022-09-28 15:00:13. It has garnered 65372 views and 1422 likes. The duration of the video is 00:08:36 or 516 seconds.
Today’s Tutorial is EASY 3×3 Spiral Piston Door For Minecraft Bedrock Edition 1.120!!! It is super simple to do! Make sure to like the video and subscribe if you want to see more helpful tutorials like this EASY 3×3 Spiral Piston Door! ______________________________________________________ Last video: https://youtu.be/yVGOKvZABvk
Sculk Sensor Activation: https://youtu.be/sCoAUioPVaw T Flip Flop: https://youtu.be/W6D9_hXL0VU Pulse Extender: https://youtu.be/9DuUE2hGDBQ ______________________________________________________
Socials:
Twitch – ImScottyO – https://www.twitch.tv/imscottyo
Discord Server: https://discord.gg/sYvgKtG69W
Instagram – imscottyo – https://www.instagram.com/imscottyo/
Twitter – ImScottyO – https://twitter.com/ImScottyO
Subscribe To The Second Channel: https://www.youtube.com/channel/UCvtsiRh8irsfnPcYabO0gVw
Subscribe here: https://www.youtube.com/channel/UCVOKNpFDtvy6Jfm_6Pi5hig
______________________________________________________ Sections: 0:00 – Intro 0:13 – Choose My Onesie 🙂 0:26 – Material List 0:39 – Tutorial 3:22 – What To Do If It Doesn’t Work 4:56 – Tutorial (Second Section) 6:36 – Adding / Moving Levers 8:21 – Outro ______________________________________________________ Leave any Minecraft tutorials you want in the comments or Discord Server! ______________________________________________________
#MinecraftBedrock #Tutorial #SpiralPistonDoor #3×3 #Easy #1.2 ______________________________________________________
See you guys in the next one!